Bostitch BT200K

Bostitch BT200K
Notice: Undefined variable: position6 in /home/domains2/public_html/ on line 186

Trigger problems When I pull the trigger air leaks out of the trigger but the gun will not fire. Do you replace the trigger assembly or just the o-rings

Posted by donnewc on Sep 26, 2008

★ ★ ★ ★ ☆ 4.0 stars

Bostitch BT200K

Product Troubleshooting for Bostitch BT200K

Notice: Undefined variable: position5 in /home/domains2/public_html/ on line 214

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Answers :

I have repaird hundreds of nail guns with a problem similar to yours. Depending on the brand and model, the problem can be repaired by checking the following. Headvalve orings should be checked for wear and any surface that the orings contact must be smooth and free from scratches. If the surfaces are scratched try to smooth with fine sandpaper and use light grease instead of oil when assembling. The safety contact foot may not be reaching high enough into the trigger to properly push in the trigger button. Check for worn spots on the trigger that may be filled in with epoxy, loose fitting trigger caused by worn roll pin or retaining pin. Some of the trigger valves as used on many bostitch nailers (tva6 valve) used a plastic pin which contacts the trigger. If this pin is loose or worn the valve should be replaced. Some tva6 valves have a vinyl looking sort of oring that fits too loose on the spool. This vinyl oring in not available by itself but if the oring fits too loose the gun will not fire and leak air. On bostitch remove the trigger and the rollpins holding the trigger valve and apply air to gun to eject valve. (use heavy glove to catch valve as it will come out with force)
Usually they come in assy

Research, Knowledge and Information :

Notice: Undefined variable: position4 in /home/domains2/public_html/ on line 266

Notice: Undefined variable: go_page in /home/domains2/public_html/ on line 277

GRT-III Trigger - Airgun Triggers - CharlieDaTuna

GRT-III Trigger - NPSS trigger,NP ... all of the trigger problems and not just reducing trigger pull. ... to remove the trigger assembly from the gun to install the ...
Read More At :

How to Diagnose Power Air Nailers :

Repair Parts Home Power Tool Articles How to Diagnose Power Air Nailers. ... and O-rings: 1. Dry fire the nailer. 2. ... Air Leaks Out Trigger.
Read More At :

Bostitch Nailgun SB-1850BN (air at trigger, does not cycle ...

Bostitch Nailgun SB-1850BN (air at trigger, does not cycle) ... press the trigger and air comes out of the trigger but the gun does not fire ... Replace O-rings.
Read More At :

Problem With Pneumatic Nail Gun - Won't Fire... - Tools - DIY ...

problem with pneumatic nail gun - won't fire... ... Air just keeps coming out of the trigger area. ... The Bostitch site says it is the trigger o rings.
Read More At :

How to Replace the Trigger Valve on your Nail Gun

... because all the air in your compressor will be hissing out around your trigger assembly. ... you’ll need to replace the trigger ... use for a nail gun. Do NOT ...
Read More At :

How to Repair you Nailer - Air Compressor Parts | Master Tool ...

... problems: • Air leak through the top head exhaust port • Nothing happens when you pull the trigger • Air leak ... by your o-rings. This is not something you ...
Read More At :

How To Install A Stanley-Bostitch TVA11 Trigger Valve - YouTube

Apr 30, 2012 · This short video shows a few useful steps on how to install a Bostitch TVA11 trigger valve ... part for your air compressor, nail gun, ... not just about ...

How To Replace The Trigger Valve On A Bostich Nail Gun. - How ...

... grease for the O rings, and a punch to drive out the ... leaking all you need to do is replace the O ... that just hisses air when i pull the trigger ...
Read More At :

Having problems with your Bostitch BT200K ?

Loading ...

Load time: 0.0138 seconds