Factory-Reconditioned DeWalt DW432R 8 Amp 3-Inch by 21-Inch...

Factory-Reconditioned DeWalt DW432R 8 Amp 3-Inch by 21-Inch...
Notice: Undefined variable: position6 in /home/domains2/public_html/howie-mandel.com/show.php on line 186

Motor runs but the drive drum that hold the sanding belt does not turn.

The motor runs and the belt pulleys are fine, but the drive drum for the sanding belt does not turn. I am unable to get the drum off of the sander to determine what is not working properly. I know the nuts are left hand, but they are recessed into the drum itself.

★ ★ ★ ★ ☆ 4.0 stars

Factory-Reconditioned DeWalt DW432R 8 Amp 3-Inch by 21-Inch...

Product Troubleshooting for Factory-Reconditioned DeWalt DW432R 8 Amp 3-Inch by 21-Inch...



Notice: Undefined variable: position5 in /home/domains2/public_html/howie-mandel.com/show.php on line 214

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Answers :


Instead of removing the drum, remove the belt and the cover over the gearbox. The gearbox cover is normaly fixed in place by screws around the drive pulley. There may be a couple of screws under the pulley, if so they can be accessed via holes in the pulley wheel itself. Check for worn or stripped gears. These gears can be replaced if need be, but if this is the case make sure you remove and clean out all the grease first and replace that aswell as it may contain bits of teeth that have come off the faulty gear. As far as I know belt sander drive rollers can not be removed without removing the drive inside the gearbox first.

Research, Knowledge and Information :



Notice: Undefined variable: position4 in /home/domains2/public_html/howie-mandel.com/show.php on line 266

Notice: Undefined variable: go_page in /home/domains2/public_html/howie-mandel.com/show.php on line 277

6” X 4” DISC & BELT SANDER OPERATING INSTRUCTIONS MODEL: W408


Hold material securely while sanding to avoid kick back. ... Push tension lever towards drive drum to tension belt. 6. ... Belt Sander does not turn on Motor slows when
Read More At : www.charnwood.net...

KRT Woodworking - Shop Built Drum Sander


Note that I had to reverse the motor to run counter-clockwise. If your motor is not reversible be sure ... launcher not a drum sander. ... and sand the drum until ...
Read More At : krtwood.com...

Dryer Drum Not Turning - Repair Parts - RepairClinic.com


Dryer drum not turning? Use our ... and then around the drive motor pulley. Over time, the belt can break ... the dryer may not turn properly. To determine if the ...
Read More At : www.repairclinic.com...

DeWALT DW433 Type 1 3 X 21 Variable Speed Belt Sander Parts


Need to fix your DW433 Type 1 3 X 21 Variable Speed Belt ... the drive pulley does not. The motor gets electricity so ... and then then the motor would not run.
Read More At : www.ereplacementparts.com...

Dryer Won't Start - Repair Parts - RepairClinic.com


Dryer won't start? ... The drive motor turns the drum and the blower wheel to exhaust the air. ... the motor will still run, but the drum will not turn.
Read More At : www.repairclinic.com...

Ron Walter's drum sander - Woodworking for engineers


Ron Walter's drum sander ... The conveyor was a 16"x 48" sanding belt and the end rollers were made of ... and a 3" on the motor so the drum is running just under ...
Read More At : woodgears.ca...

6 Belt / 9 Disc Sander - University of Wisconsin-Milwaukee


6" Belt / 9" Disc Sander (Model 31 ... MAKE SURE the sanding belt runs in the ... voltage will damage the motor. WARNING: DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE ...
Read More At : uwm.edu...

How To Fix Dryer That Won't Tumble | Dryer Repair


How To Fix A Dryer That Won't Tumble. ... a belt connected to a motor to turn the drum. ... so that the belt will not slip on the drive motor pulley or drum when ...
Read More At : www.partselect.com...

Having problems with your Factory-Reconditioned DeWalt DW432R 8 Amp 3-Inch by 21-Inch... ?

Loading ...

Load time: 0.0123 seconds