Bostitch 18 Gauge Brad Nailer 1 - 1/4IN - BT125K - 2

Bostitch 18 Gauge Brad Nailer 1 - 1/4IN - BT125K - 2
Notice: Undefined variable: position6 in /home/domains2/public_html/ on line 186

Nails won't shoot

Hi,Got a 18 gauge brad nailer. Hooked up to 100 psi compressor (my stanley staple nailer works fine). When I pull trigger, just a burst of air around trigger.Is there anything I can do or replace?thanks

★ ★ ★ ★ ☆ 4.0 stars

Bostitch 18 Gauge Brad Nailer 1 - 1/4IN - BT125K - 2

Product Troubleshooting for Bostitch 18 Gauge Brad Nailer 1 - 1/4IN - BT125K - 2

Notice: Undefined variable: position5 in /home/domains2/public_html/ on line 214

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.

Answers :

My 18 gauge Bostich brad nailer would not fire, and air came out around the trigger. Even though the gun is advertised as oil less - this is what remedied my problem - a drop of oil. I put one drop of oil in the slot where the brads come out [realizing that is where the driver is located] and left the gun upright for some time. The next time I used the gun it worked just fine. A drop of oil can also be added into the gun where the air hose is hooked up. Do not over-do the oil process, but don't ignore it.
I had same problem with my brad nailer. The piston inside the main housing seemed to be gummed up and sticking. There was a vent on the top of the cylinder for the exhaust. When I would blow through this vent it would push the piston down and the nailer would start working. This is definitely not a permanent fix but might get you through the current job before you open the cylinder and see why it is sticking.

Research, Knowledge and Information :

Notice: Undefined variable: position4 in /home/domains2/public_html/ on line 266

Notice: Undefined variable: go_page in /home/domains2/public_html/ on line 277

Problem With Pneumatic Nail Gun - Won't Fire... - Tools - DIY ...

problem with pneumatic nail gun - won't fire... hello. yesterday i rented a finish nailed (paslode) and air compressor and started installing some crown molding. no ...
Read More At :

Ryobi nail gun question? • r/Tools - reddit

Just bought a ryobi compressor kit with 3 nail guns. The only problem I have is that the guns won't shoot out any nails. They'll fire but nothing...
Read More At :

nail gun wont shoot. - DIY Chatroom Home Improvement Forum

I have several nail guns that are blowing air out of the top but wont shoot a nail.I have tried everything i can think of and i know its ... nail gun wont shoot.
Read More At :

PC BN200 brad nailer won't shoot nails - ...

OK took junkies and handymen (or women)...I have a Porter Cable BN200 18ga finish nailer that cycles but the plunger doesn't retract above the
Read More At :

Troubleshoot | Powernail

Step by step problem troubleshooting chart for powernail nailer operation. The ... + Nailer won’t move or ... Only nail to the tongue side of Tongue ...
Read More At :

We would like to show you a description here but the site won’t allow us.
Read More At :

The In's and Out's of Pneumatic Nailers - Waterfront Woods

The In's and Out's of Pneumatic Nailers By Rick Christopherson. ... This will typically shoot 5/8" to 2" nails, but blowout can occur with nails greater the 1 1/4" ...
Read More At :

Having problems with your Bostitch 18 Gauge Brad Nailer 1 - 1/4IN - BT125K - 2 ?

Loading ...

Load time: 0.0275 seconds